FYREWASH® drums

A Guide to the FYREWASH® Range: Which Gas Turbine Compressor Cleaning Fluid is Right for Your Application?

Choosing the correct gas turbine compressor cleaning chemicals for your site makes a huge difference to cleaning results and environmental impact. But how do you know which one to opt for? You need to think about your specific fouling issues and your priorities as a whole.

Today, we’re taking a closer look at FYREWASH® F1, F2, F3 and F4: popular products from our specialist gas turbine compressor cleaning range.

We’ll help guide you to decide which is right for your application and, as always, we’re on hand to answer any questions.

We also offer FYREWASH® blade wipes for manual cleaning.

The first questions to ask

When deciding which cleaning chemicals you need, there are some key questions to guide your choice:

  • What type of fouling am I dealing with?
  • Am I washing on-line, off-line, or both?
  • How much time do I have for rinsing, and is foam a problem at my site?
  • What environmental or effluent restrictions apply?

The short answer

This table gives a quick summary guide to help choose the correct cleaning chemical based on the answers you just gave:

That’s the short answer, but let’s go further and ‘show our workings’…

What do the FYREWASH® products have in common?

There are a few characteristics shared by all the FYREWASH® products we’re looking at today:

  • To prepare them, they are diluted one part concentrate to four parts demineralised water.
  • Neutral pH in solution.
  • Can be used for both on-line and off-line washing, with any injection system and can be used when the gas turbine is running at any speed and load.
  • Should be followed by a demineralised water rinse flush after an on-line wash. After an off-line wash, rinse until the run-off is clear.
  • No transport restrictions by road or sea.
  • Leave no chemical residue.
  • Have a three-year shelf life.
  • Should be used with antifreeze when the temperature falls below +10°C (50°F), and are compatible with methanol, propylene glycol and ethylene glycol. (We can also supply our own freezing point depressant.).

So, you don’t need to consider dilution or pH when choosing your product; your key considerations are:

  • Your type of fouling
  • How you wash
  • The constraints at your site

The main difference: solvent-based or water-based

Your first step is to decide whether you want a solvent or water-based chemical. Look at your foulant-types. Oily/greasy deposits dissolve more readily in a solvent than water. Water-based products suit a wide-range of everyday fouling.

  1. FYREWASH® F1 is the only solvent-based product in the range, with a high-purity hydrocarbon solvent and surfactant formulation.
  2. FYREWASH® F2, F3 and F4 are water-based.

For oil leaks and heavy, greasy fouling: FYREWASH® F1

If your site struggles with oily/greasy deposits, FYREWASH® F1is the clear choice. Our original FYREWASH® product, F1, is perfect for heavy fouling and industrial environments. It dissolves and removes oil and grease without simply lifting it from the surface, preventing it from re-depositing elsewhere in the system.

Examples of fouling FYREWASH® F1 will combat: bearing oil leaks, and hydrocarbon mist in refineries, petrochemical plants and other industrial areas.

Find out more about FYREWASH® F1 here.

When rinse time, foam or environmental limits are the priority: FYREWASH® F2

If you’ve identified rinse time, foam and/or environmental restrictions as your priorities, FYREWASH® F2 is for you.

This water-based cleaning chemical utilises a sustainable, plant-based grease-cutter and is low-foaming for a fast rinse, minimal downtime (off-line washing) and minimal effluent. FYREWASH® F2 is also readily biodegradable (more than 60% within five days, OECD 301-A test), making it the product of choice for environmentally sensitive locations.

Examples of locations FYREWASH® F2 is suited to: sites with strict environmental parameters, e.g. marine settings.

Find out more about FYREWASH® F2 here.

The all-rounder for a general-purpose, environmentally conscious clean: FYREWASH® F3

If your site doesn’t particularly suffer from oily/greasy deposits and you’re looking for an environmentally conscious all-round cleaning chemical, FYREWASH® F3 is a great choice.

This cost-effective, water-based detergent tackles a wide range of foulant types while remaining highly biodegradable.

FYREWASH® F3 is a great ‘all-rounder’ choice for sites without a particular oily fouling problem or tight foam/rinse constraints.

Find out more about FYREWASH® F3 here.

When your priority is on-line washing: FYREWASH® F4

If you’re looking for a reliable all-round cleaning detergent which maintains its cleaning properties at any temperature, FYREWASH® F4 should be your go-to.

Gas turbine compressors run at exceptionally high temperatures, and, during on-line cleaning, your detergent is subjected to those temperatures. In this situation, we need to think about cloud point: the temperature at which some cleaning solutions turn from clear to cloudy as the cleaning agents begin to separate out of the water. When a cleaning chemical reaches its cloud point, it becomes less effective and dirt that has already been lifted may redeposit.

Learn more about cloud points and cleaning chemistry in this article.

As the cleaning detergent travels through the gas turbine compressor, becoming increasingly hot, you risk the chemical reaching its cloud point and depositing foulants. This is where FYREWASH® F4 comes in.

FYREWASH® F4 has no cloud point and does not separate as the temperature rises. It keeps its cleaning properties as it travels through the compressor, and we call this “right through” on-line washing.

(FYREWASH® F1, F2 and F3 have a cloud point well above normal off-line washing temperatures, so it’s not a concern off-line.)

If you’re looking for an all-round cleaning chemical perfect for on-line washing, choose FYREWASH® F4.

Find out more about FYREWASH® F4 here.

Choosing the right cleaning chemical is just part of the answer

Carefully selecting the best cleaning chemical for your site goes a long way to ensuring optimum results. However, the chemical can only do its job if it is delivered:

  • To the surfaces that need cleaning
  • In the correct concentration

Cleaning results rely on four elements: chemical action, mechanical action, temperature and time. Most problems happen when one of them is out of balance, so we’ve highlighted some common mistakes to avoid compromising your cleaning efforts.

Over-dilution

Some operators dilute more heavily to reduce foam, but weaker solutions will not work as effectively and produce disappointing results. Read more here.

Ineffective delivery

Spray pattern and atomisation affect how much of the blade the chemical reaches. Poor coverage due to inappropriate nozzle design/placement/maintenance will leave, e.g. blade root sections uncleaned no matter which chemical you choose. Read more here.

Drain design

If foam is an issue, take note that drains can introduce air and create foam even when the wash and/or dilution itself is correct.

More help choosing a gas turbine compressor cleaning chemical

There are a lot of variables to consider when looking at fouling at a gas turbine site. Every situation is different, and contamination levels are affected by:

  • Geographical location and surrounding environment
  • Ambient temperature and season
  • Wind direction
  • Air inlet orientation and height
  • Type and condition of the inlet filtration

In this article we’ve established:

  • For oil leaks and heavy, greasy fouling: choose FYREWASH® F1
  • When rinse time, foam or environmental limits are the priority: FYREWASH® F2
  • The all-rounder, for a general-purpose, environmentally conscious clean: FYREWASH® F3
  • When your priority is on-line washing: FYREWASH® F4

However, things don’t always feel so clear-cut in the real world. If you’re unsure of the best cleaning chemical for your specific site, suffer mixed fouling, are noting disappointing results after washes, or have specific OEM requirements, please get in touch. Our team of experts will be happy to answer all your questions and make a personalised recommendation.

Martin Howarth

Post written by Martin Howarth

An extensive knowledge of mechanical and electrical engineering together with hands on experience with gas turbines provides a bedrock for his work at Rochem.

Previous postNext post
HEAD OFFICE

ROCHEM Fyrewash Ltd

5-6 Sun Valley Business Park

Winnall Close, Winchester

Hampshire

SO23 0LB

USA OFFICE

ROCHEM Fyrewash Inc
23707 West Hardy Road
Spring
Texas
77373

CERTIFICATIONS
Act accredication
Newsletter

Subscribe to our newsletter for important news and updates.