Change language
|
ROCHEM Fyrewash Ltd
5-6 Sun Valley Business Park
Winnall Close, Winchester
Hampshire
SO23 0LB
ROCHEM Fyrewash Inc
23707 West Hardy Road
Spring
Texas
77373
Subscribe to our newsletter for important news and updates.
19 Oct 2026
Compressor washing involves more than simply spraying cleaning fluid into the compressor. Although that may be how the process appears from the outside, the fluid must be precisely injected, carried through the airflow, distributed across fouled surfaces, and given enough time to interact with deposits before being rinsed away.
All of this must happen under the demanding conditions inside a gas turbine compressor, often at full load during online washing.
Understanding how cleaning fluid moves through a gas turbine compressor can help operators refine washing practices and improve overall performance.
The theory behind the cleaning circle, also known as Sinner’s Circle, shows us that cleaning is reliant on four things:
You can read more about it here, but the basic principle is that all four factors affect each other and are needed to achieve a clean.
When relating the cleaning circle to gas turbine compressor washing, the wash fluid must:
Keep the cleaning circle in mind as we look at what happens to cleaning fluid during a gas turbine compressor wash.
Once the wash fluid has been prepared, which can be done automatically to precise specifications using a wash skid, it is injected into the gas turbine compressor. Specialist wash nozzles are crucial at the injection stage, delivering fluid droplets into the high-airflow environment.
However, simply spraying wash fluid into the compressor does not guarantee an effective clean. There are many factors that affect coverage, wetting, foulant penetration and rinsing, including:
Getting the injection stage right is key to the whole cleaning process.
Once injected, the wash fluid interacts with the fast-moving air within the gas turbine compressor; the trajectory is not the same as spraying liquid onto a stationary surface. Injection location, droplet mass, and velocity all affect where and how effectively the cleaning fluid is distributed.[i]
It’s important to ensure the wash fluid reaches the blade surfaces and provides effective coverage. After all, the fluid can only clean a surface it actually touches.
Wash fluid enters the front of the compressor and travels downstream. However, its behaviour changes along the way; turbine configuration and operating conditions influence liquid distribution.
Keep in mind that cleaning fluid doesn't simply pass through every stage the same way; spray distribution at the inlet affects what happens downstream. The amount of liquid reaching different areas can vary, and it’s important to ensure effective coverage where it's needed.
Thinking back to the cleaning circle, we need to consider mechanical action: how gas turbine cleaning solution reaches and interacts with the blades.
Even an effective detergent can deliver disappointing results if the wash system provides poor coverage.
Once the cleaning liquid reaches a surface, consider two things: contact time and chemical action (remember the cleaning circle). The fluid must spread across the surface rather than simply hit it and move away.
Surfactants in cleaning chemicals reduce the surface tension of water and improve the fluid’s ability to spread across a surface, i.e. making contact with contaminants.
Once the initial foulant/wash fluid contact is achieved, time and chemical action become the key factors. The wash solution must contain the right chemicals and the correct dilution to target the specific foulant composition. For example, a gas turbine compressor operating in a forest area is likely to have sticky sap deposits, while an offshore site will have high salt content in the compressor.
While achieving contact is the first step, you must ensure the fluid reaching the fouled blades can chemically clean the foulants and has enough time to do so. OEM guidelines help determine how long to conduct soaks during offline washes for this reason.
The right wash chemicals can also help:
It’s easy to overlook foam as simply a standard feature of cleaning products. However, it’s standard for a reason: it helps cleaning chemicals ‘stick’ to a surface longer. This assists the ‘time’ factor in the cleaning circle, allowing the cleaning chemicals to do their job.
The downside of foam can be that excessive quantities increase rinse requirements, especially as it floats on the surface of effluent. Getting the balance right is essential for effective, efficient cleaning.
Read more about the role of foam here.
Removing foulants is all well and good, but what happens next is just as important. The released material must be removed from the compressor to prevent it from redepositing and/or interfering with the turbine’s airflow and productivity.
Following the wash stage, rinsing removes residual detergent and contaminants, and the effluent is flushed out for disposal. This is the end of the journey for our cleaning fluid:
Nozzle → airflow → blade surface → foulant → rinse → drain
We’ve looked at what happens to cleaning fluid when it enters a gas turbine compressor and how the cleaning circle is key to achieving effective results. Compromising on any factor has implications for the whole process, which is why the chemical and the wash hardware cannot
be considered in isolation.
Carefully selected and correctly diluted cleaning chemicals must be delivered, transported, applied to fouled surfaces, given time and conditions to interact with deposits, then rinsed away.
While it’s easy to think about that initial injection of wash fluid and assume the job is done, what happens next is crucial and worth reviewing.
If you’d like to find out more about how we can help adjust cleaning practices at your gas turbine site, please get in touch.
[i] Mund, F.C. & Pilidis, P. (2005) Online compressor washing: A numerical survey of influencing parameters (2005). Published in Proceedings of the Institution of Mechanical Engineers, Part A: Journal
Post written by Martin Howarth
An extensive knowledge of mechanical and electrical engineering together with hands on experience with gas turbines provides a bedrock for his work at Rochem.
