Best Practises for Gas Turbine Compressor Cleaning
09.23.19
Why do gas turbine compressors need cleaning?
Through normal use, your gas turbine compressor accumulates which have a negative impact on efficiency.
Contaminants including salts, hydrocarbons, sand, oil, and grease enter through the air supply and lube system and gradually coat the compressor blades.
This changes the shape of the blades meaning air doesn’t flow through the process compressor as it should.
The inefficient system not only requires more fuel to run but there is an increased risk of damage to your if the problem is ignored.
Through a properly implemented cleaning schedule, you can remove foulants before they become a problem. This maintains an efficient system and avoids the costly downtime associated with repairs.
How do I know if my compressor needs cleaning?
The best practice when it comes to cleaning is to implement a regular schedule which includes both on line and off line cleans. If you keep on top of compressor cleaning, you shouldn’t notice a build-up of foulants.
However, some tell-tale indicators may signal your compressor needs cleaning:
- Reduced
- Head
- Capacity
- Efficiency
- Pressure ratio
- Increased
- Speed
- Temperature
- Power consumption
- Intercooler pressure drop
- Vibration, thrust bearing load
- Balancing line differential pressure
As a rule of thumb, you should clean the compressor before you notice any of the following:
- A 2% reduction in power
- A 2% increase in exhaust temperature
- A 2% decrease in compressor discharge pressure
Any of the above is equivalent to a costly 4 - 5% reduction in power output.
Choosing the right products and equipment
Once you’ve decided to clean your compressor, it’s important to use the right products and equipment for a safe, thorough clean.
The chemicals you use should meet the OEM specification and for water soluble deposits and synthetic oils, select a cleaner with a detergent base.
Mineral oils however are best cleaned with a solvent based product.
is a range of specialist chemicals perfectly suited to compressor cleaning with a product designed for the full spectrum of foulant types.
Rochem also design and install the hardware required for on line and off line washes.
to discuss your specific requirements and we can advise and provide the perfect match for your turbine cleaning schedule.
How to clean a compressor off line?
A standard off line wash includes the following:
- 6 MW gas turbine: 20L chemical + 80L water injection
- 15 min. soaking
- 100L water rinsing
- Repeat if necessary
Technique
- Shut down the gas turbine and allow it to cool.
- To prepare the engine for cleaning, open the drains and IGV.
- Once fully drained, close the bleed valves.
- Begin cranking the engine on the starter.
- Inject cleaner fluid + water, commonly heated to 38⁰C - 68⁰C, into the compressor.
- The engine should then be soaked at standstill to allow the chemicals to fully break down the foulants.
- Rinse off the foulants and cleaner fluid with clean water.
- Restart the engine to dry it out.
Results
By following this best practice for off line compressor cleaning you can fully restore 100% recoverable lost performance.
How to clean a compressor on line?
A standard online wash includes the following:
- 6 MW gas turbine: 20L chemical + 80L water injection
- 100L rinsing:
- Every day with water
- Twice a week with chemical + water
Technique
- Leave the turbine running as normal: full speed, full load.
- is injected through a fixed on line leaning manifold.
- The engine is soaked and the chemicals break down foulants.
- Chemicals and foulants are rinsed off with clean water.
Results
For best results, should complement thorough off line cleans. These ‘little and often’ washes prevent foulants from building up too quickly, maintaining a healthy, efficient compressor.
In summary
It’s important to maintain an efficient compressor through a regular cleaning schedule combining off line and on line cleans.
The choice of equipment and detergents plays a big part in achieving the desired results, but once your schedule is implemented, you should enjoy a reliable, productive turbine.
Find out more
If you’ve got any questions or would like help deciding on the best detergents and equipment for cleaning your gas turbine compressor,
Our friendly, will be happy to discuss your specific requirements.
